Limited Edition Now Playing shelf, 420 stoner weed leaf vinyl record display holder
A 420 Now Playing shelf to go on your wall, with a weed leaf instead of the O, to hold the sleeve of the vinyl record you're currently listening to. Unlike my other shelves, this one's only available in one colour: green. Because of course it is.
This one is wall-mounted, but I have free-standing versions in my shop if you'd prefer to be able to be able to move it around. You can use this for records or CDs. Please see below for fitting instructions.
The shelf measures about 20cm (7 1/2") across and is about 3.5cm (1 1/4") deep.
What's In The Box?
You'll receive one shelf and fixings - screws and plugs (with a drilling template). (There are keyholes hidden in the back for the screws, which means there's nothing visible above the shelf when nothing is on it and you can't see the screws at all.)
Fitting Instructions:
Using the included template, mark where you're going to drill on the wall. Use a spirit level. Drill two 6mm holes and then insert the Rawlplugs. Screw in so that the face of each screw is 5mm from the surface of the wall, then slot the shelf onto the screws. If it's not quite tight enough or a little loose, remove and turn the screws a quarter turn whichever way you need, and repeat until it's right.
Things To Note:
It's a 3D printed item so bear in mind you'll get some surface texture, but it's only really noticeable up close and is, for me at least, part of the appeal.
I also have display shelves, a range of dividers and display solutions for your collectibles available in my shop.
Any questions just give me a shout.
Cheers
Rob
A 420 Now Playing shelf to go on your wall, with a weed leaf instead of the O, to hold the sleeve of the vinyl record you're currently listening to. Unlike my other shelves, this one's only available in one colour: green. Because of course it is.
This one is wall-mounted, but I have free-standing versions in my shop if you'd prefer to be able to be able to move it around. You can use this for records or CDs. Please see below for fitting instructions.
The shelf measures about 20cm (7 1/2") across and is about 3.5cm (1 1/4") deep.
What's In The Box?
You'll receive one shelf and fixings - screws and plugs (with a drilling template). (There are keyholes hidden in the back for the screws, which means there's nothing visible above the shelf when nothing is on it and you can't see the screws at all.)
Fitting Instructions:
Using the included template, mark where you're going to drill on the wall. Use a spirit level. Drill two 6mm holes and then insert the Rawlplugs. Screw in so that the face of each screw is 5mm from the surface of the wall, then slot the shelf onto the screws. If it's not quite tight enough or a little loose, remove and turn the screws a quarter turn whichever way you need, and repeat until it's right.
Things To Note:
It's a 3D printed item so bear in mind you'll get some surface texture, but it's only really noticeable up close and is, for me at least, part of the appeal.
I also have display shelves, a range of dividers and display solutions for your collectibles available in my shop.
Any questions just give me a shout.
Cheers
Rob
A 420 Now Playing shelf to go on your wall, with a weed leaf instead of the O, to hold the sleeve of the vinyl record you're currently listening to. Unlike my other shelves, this one's only available in one colour: green. Because of course it is.
This one is wall-mounted, but I have free-standing versions in my shop if you'd prefer to be able to be able to move it around. You can use this for records or CDs. Please see below for fitting instructions.
The shelf measures about 20cm (7 1/2") across and is about 3.5cm (1 1/4") deep.
What's In The Box?
You'll receive one shelf and fixings - screws and plugs (with a drilling template). (There are keyholes hidden in the back for the screws, which means there's nothing visible above the shelf when nothing is on it and you can't see the screws at all.)
Fitting Instructions:
Using the included template, mark where you're going to drill on the wall. Use a spirit level. Drill two 6mm holes and then insert the Rawlplugs. Screw in so that the face of each screw is 5mm from the surface of the wall, then slot the shelf onto the screws. If it's not quite tight enough or a little loose, remove and turn the screws a quarter turn whichever way you need, and repeat until it's right.
Things To Note:
It's a 3D printed item so bear in mind you'll get some surface texture, but it's only really noticeable up close and is, for me at least, part of the appeal.
I also have display shelves, a range of dividers and display solutions for your collectibles available in my shop.
Any questions just give me a shout.
Cheers
Rob
